RADIUSdesk

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

user_guide:openvpn_bridges_prep_os [2016/09/26 05:12]
admin created
user_guide:openvpn_bridges_prep_os [2016/10/06 05:33] (current)
admin
Line 14: Line 14:
 lsmod  | grep 8021q lsmod  | grep 8021q
 </​code>​ </​code>​
 +
 +------------
 +
 ===== Install Bridge Utilities ===== ===== Install Bridge Utilities =====
  
Line 22: Line 25:
 sudo apt-get install bridge-utils sudo apt-get install bridge-utils
 </​code>​ </​code>​
 +
 +-----------
 +
 ===== Configure the Interfaces ===== ===== Configure the Interfaces =====
  
-  * Edit the **/​etc/​network/​interfaces** file to contain the following configuration.+  * If your server has **only one** interface card, edit the **/​etc/​rc.local** file to contain the following:​ 
 +<WRAP center round tip 90%> 
 +We assume here the eth0 port now has the public IP address and give the dummy interface the name of eth1. Please consider this in the configurations after this page and change accordingly. 
 +</​WRAP>​ 
 + 
 +<code bash> 
 +# This script is executed at the end of each multiuser runlevel. 
 +# Make sure that the script will "exit 0" on success or any other 
 +# value on error. 
 +
 +# In order to enable or disable this script just change the execution 
 +# bits. 
 +
 +# By default this script does nothing. 
 + 
 +#Set up the dummy interface 
 +/​sbin/​modprobe dummy 
 +/sbin/ip link set name eth1 dev dummy0 
 +/​sbin/​ifconfig eth1 hw ether 00:​22:​22:​ff:​ff:​ff 
 +/sbin/ip link set eth1 up promisc on 
 + 
 +#Now add the VLAN 
 +/​sbin/​vconfig add eth1 101 
 +/sbin/ip link set eth1.101 up promisc on 
 +/sbin/brctl addbr br0.101 
 +/sbin/brctl addif br0.101 eth1.101 
 +/sbin/ip addr add 10.101.0.1/​16 dev br0.101 
 +/sbin/ip link set dev br0.101 up 
 + 
 +/​sbin/​vconfig add eth1 102 
 +/sbin/ip link set eth1.102 up promisc on 
 +/sbin/brctl addbr br0.102 
 +/sbin/brctl addif br0.102 eth1.102 
 +/sbin/ip addr add 10.102.0.1/​16 dev br0.102 
 +/sbin/ip link set dev br0.102 up 
 + 
 + 
 +/​sbin/​vconfig add eth1 103 
 +/sbin/ip link set eth1.103 up promisc on 
 +/sbin/brctl addbr br0.103 
 +/sbin/brctl addif br0.103 eth1.103 
 +/sbin/ip addr add 10.103.0.1/​16 dev br0.103 
 +/sbin/ip link set dev br0.103 up 
 + 
 +exit 0 
 + 
 +</​code>​ 
 + 
 +  * If your server has two intercace cards, edit the **/​etc/​network/​interfaces** file to contain the following configuration.
 <code bash> <code bash>
 #Remember also to configure eth1 to contain the public IP Address... #Remember also to configure eth1 to contain the public IP Address...
Line 58: Line 112:
         bridge_ports eth0.103         bridge_ports eth0.103
 </​code>​ </​code>​
 +
 +
 +-----------
 +
 ===== Confirm it is correct ===== ===== Confirm it is correct =====