Differences

This shows you the differences between two versions of the page.

--- technical:ppp-pppoe-basic [2023/10/15 04:57]
admin [Connecting a Client]
+++ technical:ppp-pppoe-basic [2023/10/15 06:56] (current)
admin [Connecting a Client]
@@ Line 39: / Line 39: @@
 mtu=1400
 mru=1400
-#accomp=deny
-#pcomp=deny
-#ccp=0
-#mppe=require
 ipv4=require
 ipv6=deny
@@ Line 49: / Line 45: @@
 ipv6-accept-peer-intf-id=1
 lcp-echo-interval=20
-#lcp-echo-failure=3
 lcp-echo-timeout=120
 unit-cache=1
-#unit-preallocate=1
 [pppoe]
 verbose=1
-#ac-name=xxx
-#service-name=yyy
-#pado-delay=0
-#pado-delay=0,100:100,200:200,-1:500
 called-sid=mac
-#tr101=1
-#padi-limit=0
-#ip-pool=pppoe
-#ipv6-pool=pppoe
-#ipv6-pool-delegate=pppoe
-#ifname=pppoe%d
-#sid-uppercase=0
-#vlan-mon=eth0,10-200
-#vlan-timeout=60
-#vlan-name=%I.%N
-#interface=eth1,padi-limit=1000
 interface=enp0s3
@@ Line 87: / Line 66: @@
 dae-server=127.0.0.1:3799,testing123
 verbose=1
-#timeout=3
-#max-try=3
-#acct-timeout=120
-#acct-delay-time=0
-#acct-delay-start=0
-#acct-on=0
-acct-interim-interval=120
-#acct-interim-jitter=0
-#default-realm=
-#strip-realm=0
-#attr-tunnel-type=My-Tunnel-Type
-#nas-port-id-in-req=1
 [client-ip-range]
@@ Line 106: / Line 73: @@
 [ip-pool]
 gw-ip-address=192.168.0.1
-#vendor=Cisco
-##attr=Cisco-AVPair
 attr=Framed-Pool
 .168.0.2-255
@@ Line 120: / Line 85: @@
 log-emerg=/var/log/accel-ppp/emerg.log
 log-fail-file=/var/log/accel-ppp/auth-fail.log
-#log-debug=/dev/stdout
-#syslog=accel-pppd,daemon
-#log-tcp=127.0.0.1:3000
 copy=1
-#color=1
-#per-user-dir=per_user
-#per-session-dir=per_session
-#per-session=1
 level=3
@@ Line 133: / Line 91: @@
 vendor=Mikrotik
 attr=Mikrotik-Rate-Limit
-#rate-multiplier=10000
-#attr=Filter-Id
-#down-burst-factor=0.1
-#up-burst-factor=1.0
-#latency=50
-#mpu=0
-#mtu=0
-#r2q=10
-#quantum=1500
-#moderate-quantum=1
-#cburst=1534
-#ifb=ifb0
 up-limiter=police
 down-limiter=tbf
-#leaf-qdisc=sfq perturb 10
-#leaf-qdisc=fq_codel [limit PACKETS] [flows NUMBER] [target TIME] [interval TIME] [quantum BYTES] [[no]ecn]
-#rate-multiplier=1
-#fwmark=1
-#rate-limit=2048/1024
-#attr-down=PPPD-Downstream-Speed-Limit
-#attr-up=PPPD-Upstream-Speed-Limit
 verbose=1
@@ Line 160: / Line 99: @@
 telnet=127.0.0.1:2000
 tcp=127.0.0.1:2001
-#password=123
-#sessions-columns=ifname,username,ip,ip6,ip6-dp,type,state,uptime,uptime-raw,calling-sid,called-sid,sid,comp,inbound-if,service-name,rx-bytes,tx-bytes,rx-bytes-raw,tx-bytes-raw,rx-pkts,tx-pkts,netns,vrf
 </file>
@@ Line 395: / Line 332: @@
         option password 'testing123'
 </code>
-  * This device is connected onto the same network (broadcast domain) where our Accel-ppp server is running so the network packets will reach the PPPoE server.
+  * This device has to be connected to the **same network** (broadcast domain) where our Accel-ppp server is running in order for the network packets to reach the PPPoE server.
 ===== Checking The Log File =====
@@ Line 406: / Line 343: @@
 <code>
 [2023-10-15 02:53:26]:  info: enp0s8: send [RADIUS(1) Access-Request id=1 <User-Name "dirk"> <NAS-Identifier "accel-ppp"> <NAS-Port-Type Virtual> <Service-Type Framed-User> <Framed-Protocol PPP> <Calling-Station-Id "c4:4b:d1:00:97:49"> <Called-Station-Id "08:00:27:08:25:67"> <User-Password 0xa8b2cc499a76d411bc05892369653482>]
-[2023-10-15 02:53:26]:  warn: enp0s8: radius:packet: vendor 26 not found
-[2023-10-15 02:53:26]:  warn: enp0s8: radius:packet: vendor 26 not found
 [2023-10-15 02:53:26]:  info: enp0s8: recv [RADIUS(1) Access-Accept id=1 <Framed-Pool "pool1"> <Framed-Protocol PPP> <Mikrotik-Rate-Limit "512k/512k 1024k/1024k 1024k/1024k 100/100"> <Framed-Compression Van-Jacobson-TCP-IP> <Vendor-Specific 0x0000372a080600000200> <Vendor-Specific 0x0000372a070600000200>]
 [2023-10-15 02:53:26]:  info: ppp1: connect: ppp1 <--> pppoe(c4:4b:d1:00:97:49)
@@ Line 416: / Line 351: @@
 </code>
+===== Using accel-cmd =====
+  * You can get more information on the current running instance of Accel-ppp by using the accel-cmd program.
+<code>
+accel-cmd show stat
+</code>
+  * Results in the following in our case
+<code>
+accel-cmd show stat
+uptime: 0.08:17:34
+cpu: 0%
+mem(rss/virt): 5240/244536 kB
+core:
+  mempool_allocated: 177084
+  mempool_available: 165700
+  thread_count: 4
+  thread_active: 1
+  context_count: 9
+  context_sleeping: 0
+  context_pending: 0
+  md_handler_count: 8
+  md_handler_pending: 0
+  timer_count: 3
+  timer_pending: 0
+sessions:
+  starting: 0
+  active: 1
+  finishing: 0
+pppoe:
+  starting: 0
+  active: 1
+  delayed PADO: 0
+  recv PADI: 4
+  drop PADI: 0
+  sent PADO: 4
+  recv PADR(dup): 4(0)
+  sent PADS: 4
+  filtered: 0
+radius(1, 164.160.89.129):
+  state: active
+  fail count: 0
+  request count: 0
+  queue length: 0
+  auth sent: 4
+  auth lost(total/5m/1m): 0/0/0
+  auth avg query time(5m/1m): 0/0 ms
+  acct sent: 7
+  acct lost(total/5m/1m): 0/0/0
+  acct avg query time(5m/1m): 0/0 ms
+  interim sent: 254
+  interim lost(total/5m/1m): 6/0/0
+  interim avg query time(5m/1m): 59/0 ms
+</code>
+  * To see the current active sessions
+<code>
+accel-cmd show sessions
+</code>
+  * Result in the following:
+<code>
+ ifname | username |    calling-sid    |     ip      | rate-limit | type  | comp | state  |  uptime
+--------+----------+-------------------+-------------+------------+-------+------+--------+----------
+ ppp0   | dirk     | c4:4b:d1:00:97:49 | 192.168.1.4 | 512/512    | pppoe |      | active | 00:48:53
+</code>

RADIUSdesk

Page Tools

Site Tools

User Tools

Differences